Part No. 10X8-56110
-
Shielded Cat6 Blue Ethernet Patch Cable, Snagless/Molded Boot, 10 foot -
Our 15 foot 3-Pin XLR Audio Cables are built with high quality XLR connectors and audio cable for maximum signal transfer and RF/EMI noise resistance. The high density shield blocks electrostatic noise, eliminating annoying hum, buzz, radio interference and noise.Part No. 10XR-01215 -
Our 15 foot 3-Pin XLR Male to 1/4 Inch Mono Male Audio Cables are built with high quality XLR and 1/4 inch connectors and audio cable for maximum signal transfer and RF/EMI noise resistance. The high density shield blocks electrostatic noise, eliminating annoying hum, buzz, radio interference and noise.Part No. 10XR-01415 -
Our 25 foot 3-Pin XLR Male to 1/4 Inch Mono Male Audio Cables are built with high quality XLR and 1/4 inch connectors and audio cable for maximum signal transfer and RF/EMI noise resistance. The high density shield blocks electrostatic noise, eliminating annoying hum, buzz, radio interference and noise.Part No. 10XR-01425 -
This 7ft Bootless Plenum Cat5e Gray Ethernet Patch Cable is perfect for short runs in buildings or government installations.The plenum rating means that the cable is jacketed in materials which have low toxicity smoke characteristics and fire retardant properties. The Plenum of a building is the area between floors or above office areas for heating/cooling airflow. This cable meets the strictest requirements for any building codes.Part No. 11X6-12107 -
This gray 20 foot snagless Cat6a cable is ideal for situations with higher environmental noise than normal. Cat6a was developed to achieve maximum distance of 100 meters for full 10-Gigabit network speeds. This robust spec will afford you the extra headroom across your network that Cat6 cannot. The 500 Mhz performance is double that of Category 6 and five times the bandwidth capacity of Category 5e. The extra performance is ideal for Power over Ethernet (PoE) and Voice Over Internet Protocol (VoIP) applications where data loss is audibly and visually seen and heard. The latest draft declares a new measurement for Power-Sum Alien Crosstalk to ensure neighboring pairs do not cause disturbance to the other cables. The cable center isolator maintains strict pair separation optimizing NEXT performance. Our Cat6a patch cables are complete end-to-end solution and are tested for compliance with all EIA/TIA-568-C Category 6 specifications. This is a shielded patch cable with molded boots (snagless installation) and extra protection for the RJ45 connector and clip. Cat6a cable includes a spline and ribbing to help ensure separation between the pairs which limits cross talk. The connectors are wired to the T568B standard. The individual conductors are 24 AWG (American wire gauge) stranded pure copper. Cat6a patch cables are stranded to improve flexibility. Pure copper conductors provide the best signal possible. The RJ45 plug features gold connectors to prevent corrosion thus ensuring a longer cable life.Part No. 13X6-52120 -
This 20 foot cable is a blue STP (Shielded Twisted Pair) patch cable with molded boots (snagless installation) and extra protection for the RJ45 connector and clip. Cat6a cable includes a spline and ribbing to help ensure separation between the pairs which limits cross talk. The connectors are wired to the T568B standard. The individual conductors are 24 AWG (American wire gauge) stranded pure copper. Cat6a patch cables are stranded to improve flexibility. Pure copper conductors provide the best signal possible. The RJ45 plug features gold connectors to prevent corrosion thus ensuring a longer cable life.Part No. 13X6-56120 -
This 25ft Cat6a Gray Slim Ethernet Patch Cable comes with a Snagless/Molded Boot and is the perfect solution to all of your Cat6a needs. The smaller diameter makes for a slimmer, more flexible cable that will fit well into cluttered data centers and other places where space is tight. With speeds up to 500 MHz, this cable twice as fast as regular Cat6. Our Cat6a patch cables are tested for compliance with all EIA/TIA-568-C Category 6a specifications.Part No. 13X6-62125 -
This white Decora Wall Plate Insert is designed with a VGA coupler and three RCA couplers. It is used with a Decora style wallplate (not included).Part No. 301-4001 -
This white Decora wall plate insert works with VGA/HD15, 3.5mm and three red/white/yellow RCA couplers.Part No. 301-5000 -
This SC and ST Fiber Dust Cap will save your fiber optic cable from contamination by dust and/or dirt. Comes in a bag of 100 pieces.Part No. 30SX-010HD -
This ivory 1.25 inch raceway piece serves as a junction for three straight cable raceway runs coming together (one of the runs will be perpendicular to the other two). It allows the installer to connect three longer straight raceway sections at a junction spot. Use surface mount cable raceways to protect and tidy up cable runs around the home or office where running through walls is not possible or practical. These raceways are useful for nearly any type of cable from phone, network, USB, VGA, Audio/Video, Speaker and more. Some sample applications would be: office cubicles where walls are not available or the working space can change configuration or in the existing home where one wants to install surround speakers and hide/protect the speaker cables/wires.Part No. 31R2-006IV -
This white 1.25 inch raceway piece serves as a junction for three straight cable raceway runs coming together (one of the runs will be perpendicular to the other two). It allows the installer to connect three longer straight raceway sections at a junction spot. Use surface mount cable raceways to protect and tidy up cable runs around the home or office where running through walls is not possible or practical. These raceways are useful for nearly any type of cable from phone, network, USB, VGA, Audio/Video, Speaker and more. Some sample applications would be: office cubicles where walls are not available or the working space can change configuration or in the existing home where one wants to install surround speakers and hide/protect the speaker cables/wires.Part No. 31R2-006WH -
This 1 meter (~3 feet) fiber optic cable is terminated with LC (Lucent Connector) connectors on both ends. It is a singlemode fiber (9 micron core) designed to transmit data across long distances at high speeds. The cord is duplex (two fibers) which means it permits synchronous communication between devices. The cladding diameter is 125 microns. (Not for Home Theater)Part No. LCLC-01201 -
This 2 meter (~6 feet) fiber optic cable is terminated with LC (Lucent Connector) connectors on both ends. It is a singlemode fiber (9 micron core) designed to transmit data across long distances at high speeds. The cord is duplex (two fibers) which means it permits synchronous communication between devices. The cladding diameter is 125 microns. (Not for Home Theater)Part No. LCLC-01202 -
This 2 meter (~6 feet) fiber optic cable is terminated with LC (Lucent Connector) connectors on both ends. It is a multimode fiber (50 micron core) designed to transmit data across shorter distances at LAN speeds. The cord is duplex (two fibers) which means it permits synchronous communication between devices. The cladding diameter is 125 microns. (Not for Home Theater)Part No. LCLC-11002 -
This 2 meter (~6 feet) fiber optic cable is terminated with LC (Lucent Connector) connectors on both ends. It is a multimode fiber (62.5 micron core) designed to transmit data across shorter distances at LAN speeds. The cord is duplex (two fibers) which means it permits synchronous communication between devices. The cladding diameter is 125 microns. (Not for Home Theater)Part No. LCLC-11102 -
This Aqua Blue jacketed 2 meter (~6 feet) 10 gigabit rated fiber optic cable is terminated with LC (Lucent Connector) connectors on both ends. It is a multimode fiber (50 micron core) designed to transmit data across shorter distances at LAN speeds. The cord is duplex (two fibers) which means it permits synchronous communication between devices. The cladding diameter is 125 microns. (Not for Home Theater)Part No. LCLC-31002 -
This 1 meter (~3.3 feet) aqua 10 gigabit rated fiber optic cable is terminated with LC (Lucent Connector) connectors on both ends. It is a multimode fiber (50 micron core) designed to transmit data across shorter distances at LAN speeds. The cord is duplex (two fibers) which means it permits synchronous communication between devices. The cladding diameter is 125 microns.Part No. LCLC-41001 -
This 3 meter (~10 feet) fiber optic cable is terminated with a LC (Lucent Connector) connector on one end and a SC (Subscriber Connector) connector on the other end. It is a singlemode fiber (9 micron core) designed to transmit data across long distances at high speeds. The cord is duplex (two fibers) which means it permits synchronous communication between devices. The cladding diameter is 125 microns. (Not for Home Theater)Part No. LCSC-01203 -
This 6 meter (~19 feet) fiber optic cable is terminated with a LC (Lucent Connector) connector on one end and a SC (Subscriber Connector) connector on the other end. It is a multimode fiber (50 micron core) designed to transmit data across shorter distances at LAN speeds. The cord is duplex (two fibers) which means it permits synchronous communication between devices. The cladding diameter is 125 microns. (Not for Home Theater)Part No. LCSC-11006 -
This 2 meter (~6 feet) fiber optic cable is terminated with a LC (Lucent Connector) connector on one end and a SC (Subscriber Connector) connector on the other end. It is a multimode fiber (62.5 micron core) designed to transmit data across shorter distances at LAN speeds. The cord is duplex (two fibers) which means it permits synchronous communication between devices. The cladding diameter is 125 microns. (Not for Home Theater)Part No. LCSC-11102 -
This Aqua Blue jacketed 1 meter (~3 feet) 10 gigabit rated fiber optic cable is terminated with a LC (Lucent Connector) connector on one end and a SC (Subscriber Connector) connector on the other end. It is a multimode fiber (50 micron core) designed to transmit data across shorter distances at LAN speeds. The cord is duplex (two fibers) which means it permits synchronous communication between devices. The cladding diameter is 125 microns. (Not for Home Theater)Part No. LCSC-31001 -
This 1 meter (~3 feet) fiber optic cable is terminated with a LC (Lucent Connector) connector on one end and a ST (Straight Tip/Bayonet Connector) connector on the other end. It is a multimode fiber (62.5 micron core) designed to transmit data across shorter distances at LAN speeds. The cord is duplex (two fibers) which means it permits synchronous communication between devices. The cladding diameter is 125 microns. (Not for Home Theater)Part No. LCST-11101 -
This 1 meter (~3 feet) fiber optic cable is terminated with SC (Subscriber Connector) connectors on both ends. It is a singlemode fiber (9 micron core) designed to transmit data across long distances at high speeds. The cord is duplex (two fibers) which means it permits synchronous communication between devices. The cladding diameter is 125 microns. (Not for Home Theater)Part No. SCSC-01201 -
This 4 meter (~13 feet) fiber optic cable is terminated with SC (Subscriber Connector) connectors on both ends. It is a singlemode fiber (9 micron core) designed to transmit data across long distances at high speeds. The cord is duplex (two fibers) which means it permits synchronous communication between devices. The cladding diameter is 125 microns. (Not for Home Theater)Part No. SCSC-01204 -
This 4 meter (~13 feet) fiber optic cable is terminated with SC (Subscriber Connector) connectors on both ends. It is a multimode fiber (50 micron core) designed to transmit data across shorter distances at LAN speeds. The cord is duplex (two fibers) which means it permits synchronous communication between devices. The cladding diameter is 125 microns. (Not for Home Theater)Part No. SCSC-11004 -
This 2 meter (~6 feet) fiber optic cable is terminated with SC (Subscriber Connector) connectors on both ends. It is a multimode fiber (62.5 micron core) designed to transmit data across shorter distances at LAN speeds. The cord is duplex (two fibers) which means it permits synchronous communication between devices. The cladding diameter is 125 microns. (Not for Home Theater)Part No. SCSC-11102 -
This Aqua Blue jacketed 1 meter (~3 feet) 10 gigabit rated fiber optic cable is terminated with SC (Subscriber Connector) connectors on both ends. It is a multimode fiber (50 micron core) designed to transmit data across shorter distances at LAN speeds. The cord is duplex (two fibers) which means it permits synchronous communication between devices. The cladding diameter is 125 microns. (Not for Home Theater)Part No. SCSC-31001 -
This 1 meter (~3 feet) fiber optic cable is terminated with a SC (Subscriber Connector) connector on one end and a ST (Straight Tip/Bayonet Connector) on the other end. It is a singlemode fiber (9 micron core) designed to transmit data across long distances at high speeds. The cord is duplex (two fibers) which means it permits synchronous communication between devices. The cladding diameter is 125 microns. (Not for Home Theater)Part No. SCST-01201 -
This 1 meter (~3 feet) fiber optic cable is terminated with a SC (Subscriber Connector) connector on one end and a ST (Straight Tip/Bayonet Connector) connector on the other end. It is a multimode fiber (50 micron core) designed to transmit data across shorter distances at LAN speeds. The cord is duplex (two fibers) which means it permits synchronous communication between devices. The cladding diameter is 125 microns. (Not for Home Theater)Part No. SCST-11001 -
This 1 meter (~3 feet) fiber optic cable is terminated with a SC (Subscriber Connector) connector on one end and a ST (Straight Tip/Bayonet Connector) connector on the other end. It is a multimode fiber (62.5 micron core) designed to transmit data across shorter distances at LAN speeds. The cord is duplex (two fibers) which means it permits synchronous communication between devices. The cladding diameter is 125 microns. (Not for Home Theater)Part No. SCST-11101 -
This 1 meter (~3 feet) fiber optic cable is terminated with ST (Straight Tip/Bayonet Connector) connectors on both ends. It is a singlemode fiber (9 micron core) designed to transmit data across long distances at high speeds. The cord is duplex (two fibers) which means it permits synchronous communication between devices. The cladding diameter is 125 microns. (Not for Home Theater)Part No. STST-01201 -
This 1 meter (~3 feet) fiber optic cable is terminated with ST (Straight Tip/Bayonet Connector) connectors on both ends. It is a multimode fiber (50 micron core) designed to transmit data across shorter distances at LAN speeds. The cord is duplex (two fibers) which means it permits synchronous communication between devices. The cladding diameter is 125 microns. (Not for Home Theater)Part No. STST-11001 -
This 1 meter (~3 feet) fiber optic cable is terminated with ST (Straight Tip/Bayonet Connector) connectors on both ends. It is a multimode fiber (62.5 micron core) designed to transmit data across shorter distances at LAN speeds. The cord is duplex (two fibers) which means it permits synchronous communication between devices. The cladding diameter is 125 microns. (Not for Home Theater)Part No. STST-11101 -
High Density Female Crimp Contacts, 100 Pieces. High Density Female Crimping Contacts (100 Pieces Per Bag). Works for our female HD15 connectors, Part Number: 3530-04115.Part No. 3300-104HD -
2-Gang Recessed Low Voltage Cable Plate, BlackPart No. 45-0002-BK -
2-Gang Recessed Low Voltage Cable Plate, BrownPart No. 45-0002-BR -
2-Gang Recessed Low Voltage Cable Plate, Lite AlmondPart No. 45-0002-LA -
2-Gang Recessed Low Voltage Cable Plate, WhitePart No. 45-0002-WH -
LGX Styled Blank plate with No Holes Unloaded - Black Powder Coat. Cover up unused LGX slots in our fiber patch panels with this LGX Styled Adapter Plates are easy snap-in style mount for use in Rack and wall-mount enclosures. Available in black powder coat. Details- 5.1 inch (130mm) x 1.13 inch (28.7mm)
- Easy snap-in mounting in FIS Rack and wallmount enclosures
- Multimode adapters utilize a phosphour bronze alignment sleeve
- Singlemode and APC adapter utilize a ceramic alignment sleeve
- Available in black powder coat
- LGX Compatible
Part No. 68F1-20010 -
2 Port USB Wall Travel Charger, dual USB A female ports, 5V/2 1A output, Folding plug, White. This two port travel USB wall charger has two USB A female ports for charging two devices at the same time. The compact size and folding prongs make it essay to store in a bag for trips. The body of the charger is white. Suitable for use with tablets, mobile phones, Bluetooth speakers, and other devices with the USB interface. specifications- Output: 5 V 3.4A total(both ports)
- Size: 46 x 45 x 25 mm
- Ports: 2 USB A female
Part No. 90W1-30310WH -
DisplayPort v1.4 Video Cable, 32.4 Gbit/s Data Rate, 8k@60Hz / 4k@120Hz, DisplayPort Male, 3 footPart No. 10H1-70103 -
Cat6a Green Slim Ethernet Patch Cable, Pure Copper, Snagless Molded Boot, 25 footPart No. 13X6-65125 -
Cat6a Yellow Slim Ethernet Patch Cable, Pure Copper, Snagless Molded Boot, 25 footPart No. 13X6-68125 -
Cat6a White Slim Ethernet Patch Cable, Pure Copper, Snagless Molded Boot, 25 footPart No. 13X6-69125 -
Computer / Monitor Power Extension Cord, Black, C13 to C14, 14AWG,15 Amp, 3 footPart No. 10W2-02203 -
Computer / Monitor Power Extension Cord, Blue, C13 to C14, 14AWG,15 Amp, 3 footPart No. 10W2-02203BL
