-
24 Fiber Indoor/Outdoor Fiber Optic Cable, Multimode 50/125 OM3, Plenum Rated, Black, Spool, 1000ft -
Our yellow bulk 1000 foot solid Cat6a Shielded Ethernet cable comes in a convenient spool and is ideal for the person looking to make longer permanent network runs during installation/expansion of network infrastructure. Cat6a was developed to achieve maximum distance of 100 meters for full 10-Gigabit network speeds. This robust spec will afford you the extra headroom across your network that Cat6 can not. The 500 Mhz performance is double that of Category 6 and five times the bandwidth capacity of Category 5e. The extra performance is ideal for Power over Ethernet (PoE) and Voice Over Internet Protocol (VoIP) applications where data loss is audibly and visually seen and heard. The latest draft declares a new measurement for Power-Sum Alien Crosstalk to ensure neighboring pairs do not cause disturbance to the other cables. The cable center isolator maintains strict pair separation optimizing NEXT performance. Our Cat6a bulk cable tested for compliance with all EIA/TIA-568-C Category 6a specifications. This particular cable is a yellow shielded solid cable. Cat6a cable includes a spline and ribbing to help ensure separation between the pairs which limits cross talk. The individual conductors are 23 AWG (American wire gauge) solid pure copper. Pure copper conductors provide the best signal possible. This bulk CAT6a cable will not be able to be crimped onto any connectors. The wires are simply too thick to fit. This cable should be punched down into a CAT6a keystone jack on one end and patch panel on the other end.Part No. 13X6-581NH -
Plenum rated coating on wire burns at a much higher temperature and emits fewer fumes, ideal for use in walls and ceilings. CAT-5E cables are primarily used for networking, data transfer, and phone lines. CAT-5E cables can support 10 / 100 / 1000Mbps. We offer a wide selection of colors.Part No. 11X6-022TH -
Security/Alarm Wire, Gray, 16/2 (16AWG 2-Conductor), Stranded, CM / Inwall rated, Pullbox, 1000 foot -
Security/Alarm Wire, Gray, 16/4 (16AWG 4-Conductor), Stranded, CM / Inwall rated, Pullbox, 1000 foot -
Security/Alarm Wire, Gray, 18/2 (18AWG 2 Conductor), Stranded, CMR / Inwall rated, Pullbox, 1000 foot -
Security/Alarm Wire, White, 18/2 (18AWG 2 Conductor), Stranded, CMR / Inwall rated, Pullbox, 1000 foot -
Security/Alarm Wire, White, 18/4 (18AWG 4 Conductor), Stranded, CMR / Inwall rated, Pullbox, 1000 foot -
Security/Alarm Wire, Gray, 22/2 (22AWG 2 Conductor), Solid, CMR / In-wall rated, Pullbox, 1000 foot -
Security/Alarm Wire, White, 22/2 (22AWG 2 Conductor), Solid, CMR / Inwall rated, Pullbox, 1000 foot -
Security/Alarm Wire, Gray, 22/2 (22AWG 2 Conductor), Stranded, CMR / In-wall rated, Pullbox, 1000 foot -
Security/Alarm Wire, White, 22/2 (22AWG 2 Conductor), Stranded, CMR / Inwall rated, Pullbox, 1000 foot
-
1000ft 12-Fiber OM4 Fiber Optic Cable 10-Gbit, OutdoorPart No. 10F3-412NH -
Fire Alarm / Security Cable, Red, 14/2 (14 AWG 2 Conductor), Solid, FPLR, Spool, 1000 foot -
Fire Alarm / Security Cable, Red, 16/2 (16 AWG 2 Conductor), Solid, FPLR, Pullbox, 1000 foot -
Fire Alarm / Security Cable, Red, 16/2 (16 AWG 2 Conductor), Solid, FPLR, Spool, 1000 foot
-
Fire Alarm / Security Cable, Red, 16/4 (16 AWG 4 Conductor), Solid, FPLR, Spool, 1000 foot -
Fire Alarm / Security Cable, Red, 18/2 (18 AWG 2 Conductor), Solid, FPLR, Pullbox, 1000 foot -
Security/Alarm Wire, Gray, 22/4 (22AWG 4 Conductor), Solid, CMR, Pullbox, 1000 foot -
Fire Alarm / Security Cable, Red, 22/4 (22 AWG 4 Conductor), Solid, FPLR, Pullbox, 1000 foot
-
Security/Alarm Wire, White, 22/4 (22AWG 4 Conductor), Solid, CMR / Inwall rated, Pullbox, 1000 foot -
Security/Alarm Wire, White, 22/4 (22AWG 4 Conductor), Stranded, CMR / Inwall rated, Pullbox, 1000 foot
-
Security/Alarm Wire, Gray, 22/6 (22AWG 6 Conductor), Stranded, CM / Inwall rated, Pullbox, 1000 foot -
Our 1000 foot white 22 AWG (American Wire Gauge) 6 conductor stranded security/alarm wire comes in easy to use pull boxes. This wire is CMR / in-wall and riser rated; it is not intended for plenum applications. This security wire is designed for use in security/alarm systems. It is typically used for connecting motion sensors, keypads, magnetic contacts, glass breaks (acoustic detectors), smoke detectors, communicators, sounders/strobes, entry management and control panels in such systems. When wiring a system please be sure to consult the manufacturers' recommendations for wire conductors, gauge and expected resistance.Part No. 10K4-5691SH -
Security/Alarm Wire, White, 22/6 (22AWG 6 Conductor), Stranded, CMR / Inwall rated, Pullbox, 1000 foot -
24 Fiber Indoor/Outdoor Fiber Optic Cable, Multimode, 50/125, OM4, 10 Gbit, Black, Riser Rated, Spool, 1000 foot -
48 Fiber Indoor/Outdoor Fiber Optic Cable, Multimode 50/125, Corning Clear Curve OM3, Plenum Rated, Black, Spool, 1000ft -
1000ft 6-Fiber OM4 Fiber Optic Cable 10-Gbit, OutdoorPart No. 10F3-406NH -
This is an aqua bulk 1000 foot spool of fiber optic distribution cable intended for large installations of short range runs at 10 Gigabit speeds. It is composed of 12 multimode fibers (50 micron core) inside an Aramid yarn wrapped in a aqua PVC outer jacket. Multimode fiber is optimized to work with fiber optic equipment using light wave lengths of 850nm (nanometers) or 1300nm. The cladding diameter is 125 microns. The Graded-Step core and cladding of our aqua bulk 50/125 distribution fiber optic cable is constructed using a high quality multimode fiber that is compliant with TIA/EIA 455-220A and IEC 60793-1-49. It also maintains compliance with legacy and LED based systems per TIA/EIA 455-204 and IEC 607-1-41. This particular cable is Riser Rated (CMR) meaning it complies with UL-1666. It is for usage in vertical tray applications without environmental air. Examples being: cable runs between floors through cable risers or in elevator shafts. These cables self extinguish and prevent the flame from traveling up the cable in a vertical burn test. This fiber optic cable is solidly constructed, UL rated and RoHS Compliant.Part No. 10F2-312NH -
1000ft Aqua 12-Fiber OM4 Fiber Optic Cable 10-GbitPart No. 10F2-412NH -
This is an aqua bulk 1000 foot spool of fiber optic distribution cable intended for large installations of short range runs at 10 Gigabit speeds. It is composed of 2 multimode fibers (50 micron core) inside an Aramid yarn wrapped in a aqua PVC outer jacket. Multimode fiber is optimized to work with fiber optic equipment using light wave lengths of 850nm (nanometers) or 1300nm. The cladding diameter is 125 microns. The Graded-Step core and cladding of our aqua bulk 50/125 distribution fiber optic cable is constructed using a high quality multimode fiber that is compliant with TIA/EIA 455-220A and IEC 60793-1-49. It also maintains compliance with legacy and LED based systems per TIA/EIA 455-204 and IEC 607-1-41. This particular cable is Riser Rated (CMR) meaning it complies with UL-1666. It is for usage in vertical tray applications without environmental air. Examples being: cable runs between floors through cable risers or in elevator shafts. These cables self extinguish and prevent the flame from traveling up the cable in a vertical burn test. This fiber optic cable is solidly constructed, UL rated and RoHS Compliant.Part No. 10F2-302NH -
2 Fiber Indoor Distribution Fiber Optic Cable, Multimode, 50/125, OM3, 10 Gbit, Aqua, Riser Rated, Spool, 1000 foot -
2 Fiber Indoor Distribution Fiber Optic Cable, Multimode, 50/125, OM4, 10 Gbit, Aqua, Riser Rated, Spool, 1000 foot -
24 Fiber Indoor Distribution Fiber Optic Cable, Multimode, 50/125, OM3, 10 Gbit, Aqua, Riser Rated, Spool, 1000 foot
-
24 Fiber Indoor Distribution Fiber Optic Cable, Multimode, 50/125, OM4, 10 Gbit, Aqua, Riser Rated, Spool, 1000 foot
-
This is an aqua bulk 1000 foot spool of fiber optic distribution cable intended for large installations of short range runs at 10 Gigabit speeds. It is composed of 6 multimode fibers (50 micron core) inside an Aramid yarn wrapped in a aqua PVC outer jacket. Multimode fiber is optimized to work with fiber optic equipment using light wave lengths of 850nm (nanometers) or 1300nm. The cladding diameter is 125 microns. The Graded-Step core and cladding of our aqua bulk 50/125 distribution fiber optic cable is constructed using a high quality multimode fiber that is compliant with TIA/EIA 455-220A and IEC 60793-1-49. It also maintains compliance with legacy and LED based systems per TIA/EIA 455-204 and IEC 607-1-41. This particular cable is Riser Rated (CMR) meaning it complies with UL-1666. It is for usage in vertical tray applications without environmental air. Examples being: cable runs between floors through cable risers or in elevator shafts. These cables self extinguish and prevent the flame from traveling up the cable in a vertical burn test. This fiber optic cable is solidly constructed, UL rated and RoHS Compliant.Part No. 10F2-306NH -
6 Fiber Indoor Distribution Fiber Optic Cable, Multimode, 50/125, OM4, 10 Gbit, Aqua, Riser Rated, Spool, 1000 foot
-
This is an aqua bulk 1000 foot spool of plenum fiber optic distribution cable intended for large installations of short range runs at 10 Gigabit speeds. It is composed of 12 multimode fibers (50 micron core) inside an Aramid yarn wrapped in a aqua PVC outer jacket. Multimode fiber is optimized to work with fiber optic equipment using light wave lengths of 850nm (nanometers) or 1300nm. The cladding diameter is 125 microns. The Graded-Step core and cladding of our aqua bulk 50/125 distribution fiber optic cable is constructed using a high quality multimode fiber that is compliant with TIA/EIA 455-220A and IEC 60793-1-49. It also maintains compliance with legacy and LED based systems per TIA/EIA 455-204 and IEC 607-1-41. This particular cable is Plenum Rated. Plenum spaces are the area between floors or above office areas for heating/cooling airflow. If an office were to catch fire, this plenum area could easily allow the spread of the fire to more floors or across the entire building. Plenum rated cables are jacketed with a fire-retardant plastic jacket of either a low-smoke polyvinyl chloride (PVC) or a fluorinated ethylene polymer (FEP) for less toxicity during a fire.Part No. 11F2-312NH -
1000ft Aqua Plenum 12-Fiber Distribution Cable, 50/125, OM4Part No. 11F2-412NH -
This is an aqua bulk 1000 foot spool of plenum fiber optic distribution cable intended for large installations of short range runs at 10 Gigabit speeds. It is composed of 2 multimode fibers (50 micron core) inside an Aramid yarn wrapped in a aqua PVC outer jacket. Multimode fiber is optimized to work with fiber optic equipment using light wave lengths of 850nm (nanometers) or 1300nm. The cladding diameter is 125 microns. The Graded-Step core and cladding of our aqua bulk 50/125 distribution fiber optic cable is constructed using a high quality multimode fiber that is compliant with TIA/EIA 455-220A and IEC 60793-1-49. It also maintains compliance with legacy and LED based systems per TIA/EIA 455-204 and IEC 607-1-41. This particular cable is Plenum Rated. Plenum spaces are the area between floors or above office areas for heating/cooling airflow. If an office were to catch fire, this plenum area could easily allow the spread of the fire to more floors or across the entire building. Plenum rated cables are jacketed with a fire-retardant plastic jacket of either a low-smoke polyvinyl chloride (PVC) or a fluorinated ethylene polymer (FEP) for less toxicity during a fire.Part No. 11F2-302NH -
1000ft Aqua Plenum 2-Fiber Distribution Cable, 50/125, OM4Part No. 11F2-402NH -
24 Fiber Indoor Distribution Fiber Optic Cable, Multimode 50/125 OM3, Plenum Rated, Aqua, Spool, 1000ft
-
24 Fiber Indoor Distribution Fiber Optic Cable, Multimode 50/125 OM4, Plenum Rated, Aqua, Spool, 1000ft
-
This is an aqua bulk 1000 foot spool of plenum fiber optic distribution cable intended for large installations of short range runs at 10 Gigabit speeds. It is composed of 6 multimode fibers (50 micron core) inside an Aramid yarn wrapped in a aqua PVC outer jacket. Multimode fiber is optimized to work with fiber optic equipment using light wave lengths of 850nm (nanometers) or 1300nm. The cladding diameter is 125 microns. The Graded-Step core and cladding of our aqua bulk 50/125 distribution fiber optic cable is constructed using a high quality multimode fiber that is compliant with TIA/EIA 455-220A and IEC 60793-1-49. It also maintains compliance with legacy and LED based systems per TIA/EIA 455-204 and IEC 607-1-41. This particular cable is Plenum Rated. Plenum spaces are the area between floors or above office areas for heating/cooling airflow. If an office were to catch fire, this plenum area could easily allow the spread of the fire to more floors or across the entire building. Plenum rated cables are jacketed with a fire-retardant plastic jacket of either a low-smoke polyvinyl chloride (PVC) or a fluorinated ethylene polymer (FEP) for less toxicity during a fire.Part No. 11F2-306NH -
This is a aqua bulk 1000 foot spool of Plenum Zipcord fiber optic cable intended for large installations where you are completing the terminations. It is a multimode fiber (50 micron core) designed to transmit data across shorter distances at 10 Gigabit speeds. Multimode fiber is optimized to work with fiber optic equipment using light wave lengths of 850nm (nanometers) or 1300nm. The cord is duplex (two fibers) which means it permits synchronous communication between devices. The cladding diameter is 125 microns. The Graded-Step core and cladding of our aqua bulk 50/125 fiber optic cable is constructed using a high quality multimode fiber that is compliant with TIA/EIA 455-220A and IEC 60793-1-49. It also maintains compliance with legacy and LED based systems per TIA/EIA 455-204 and IEC 607-1-41. This particular cable is Plenum Rated. Plenum spaces are the area between floors or above office areas for heating/cooling airflow. If an office were to catch fire, this plenum area could easily allow the spread of the fire to more floors or across the entire building. Plenum rated cables are jacketed with a fire-retardant plastic jacket of either a low-smoke polyvinyl chloride (PVC) or a fluorinated ethylene polymer (FEP) for less toxicity during a fire.Part No. 11F1-301NH -
This is a aqua bulk 1000 foot spool of Zipcord fiber optic cable intended for large installations where you are completing the terminations. It is a multimode fiber (50 micron core) designed to transmit data across shorter distances at 10 Gigabit speeds. Multimode fiber is optimized to work with fiber optic equipment using light wave lengths of 850nm (nanometers) or 1300nm. The cord is duplex (two fibers) which means it permits synchronous communication between devices. The cladding diameter is 125 microns. The Graded-Step core and cladding of our aqua bulk 50/125 fiber optic cable is constructed using a high quality multimode fiber that is compliant with TIA/EIA 455-220A and IEC 60793-1-49. It also maintains compliance with legacy and LED based systems per TIA/EIA 455-204 and IEC 607-1-41. This particular cable is Riser Rated (CMR) meaning it complies with UL-1666. It is for usage in vertical tray applications without environmental air. Examples being: cable runs between floors through cable risers or in elevator shafts. These cables self extinguish and prevent the flame from traveling up the cable in a vertical burn test. This fiber optic cable is solidly constructed, UL rated and RoHS Compliant.Part No. 10F1-301NH -
Bulk Zipcord Fiber Optic Cable, Multimode, Duplex, 50/125, OM3, Aqua, Riser Rated, Spool, 1000 foot
-
This is a black bulk 1000 foot spool of indoor/outdoor rated fiber optic distribution cable intended for large installations of short range runs at 10 Gigabit speeds. It is composed of 12 multimode fibers (50 micron core) inside a water blocking Aramid yarn wrapped in a black PVC outer jacket. Multimode fiber is optimized to work with fiber optic equipment using light wave lengths of 850nm (nanometers) or 1300nm. The cladding diameter is 125 microns. The Graded-Step core and cladding of our black bulk 50/125 indoor/outdoor fiber optic cable is constructed using a high quality multimode fiber that is compliant with TIA/EIA 455-220A and IEC 60793-1-49. It also maintains compliance with legacy and LED based systems per TIA/EIA 455-204 and IEC 607-1-41. This particular cable is Riser Rated (CMR) meaning it complies with UL-1666. It is for usage in vertical tray applications without environmental air. Examples being: cable runs between floors through cable risers or in elevator shafts. These cables self extinguish and prevent the flame from traveling up the cable in a vertical burn test. This fiber optic cable is solidly constructed, UL rated and RoHS Compliant.Part No. 10F3-312NH
The Connectivity Center is a supplier of some of the leading physical cybersecurity technologies and physical data security products. We pride ourselves in quality, value, variety, and versatility. We want to be a one-stop shop for most of your physical cybersecurity needs, and we love to serve our partners in this evolving industry.
ACCOUNT
RESOURCES
INFO
The Connectivity Center is committed to ensuring that its website is accessible to people with disabilities. We strive to have all pages on our website meet W3C Web Content Accessibility Guidelines 2.0, Level AA conformance. Any issues should be reported to [email protected].
Copyright © 2012 –    |   The Connectivity Center   |   All Rights Reserved   |   Powered by LeadWorks
